|
|
|
Engine
|
|
Enigne running or not, doesn't matter, but the engine has to be running when you set the timing (duh) so just make sure it is unplugged when you are attempting to set the timing. I think Supernova455 suggests disconnecting the battery to clear codes
|
|
Drivetrain
|
|
just got it today GM #: 7837378 it was like 7.50
|
|
Engine
|
|
My aero has an Iron intake but I beleive it was a remanufactured engine (not stock)
|
|
Non-Technical SS Discussion
|
|
Welcome!
|
|
Drivetrain
|
|
Originally Posted By: 02intimidatorHow did you come up with a 415 stroker? 383 and 434 are the only sb stokers you can get with a stock 350 or 400 block and a large stroke crank. Give Pro torque a call for the convertor. Your mistaken, I have a 42
|
|
Your SS
|
|
yea im not dealing with paching im just repalcing the whole roof the guy ahd bondo on it when i got the car couldnt find were it was leaking and pushed out all the bondo the deside to resore it
|
|
Non-Technical SS Discussion
|
|
Originally Posted By: BuzzLOL.. WHERE do I have to go to see the pictures? http://www.montecarloss.com/photopost/showgallery.php?cat=500&ppuser=10814
|
|
Rolling Chassis
|
|
MAP, Great topic. As you see by the signature, the monte should push out about 435-450 hp to the flywheel. That being said I've tried two different types of drag radials, each with their own ups and downs which I will explain. Teh car they have
|
|
Engine
|
|
There is also a thin tube going down to the cat converter. A very small u bolt holds it on. I pulled mine off, and tightened that u bolt up with a bolt stuck inside the tube to prevent leakage. You can see it here in the lower left of this picture.
|
|
Northeast
|
|
Just checked my shaft. Sometimes it wiggles more then others. Hope this helps......
|
|
Rolling Chassis
|
|
Hi Folks, Here's a link to a page that shows a 3/4 front-view sketch of what an MCSS might look like with modestly stretched fenders and quarter panels: http://www.montecarloss.com/community/ubbthreads.php?ubb=showflat&Number=337715&page=4
|
|
Rolling Chassis
|
|
yea if u got to auto zone or some thing they can get them acutlly if u no were d and a auto parts is in spots wood they carry thats stuff i got my upper boots from there when i did the brake and spindle swap on my 86
|
|
General Technical Discussions
|
|
I have a tech 2 and a tech 1 at work so I just use those.
|
|
Engine
|
|
Is this going be a daily driven ride. If so I would not go too wild on the cam you want to keep good botton end. Here another cam that be great in a daily diven car yet still sound good. http://www.summitracing.com/parts/SUM-1102/
|
|
SouthEastern Monte Carlo Club (SMCC)
|
|
Originally Posted By: MC87SSGood Morning Everyone Its Friday at last. And I am finally home. Been on a bus ALLLLLLL day long.
|
|
General Technical Discussions
|
|
Thanks,i have a friend that will do the work,and that is definately the kind of cheap i was talking about
|
|
Drivetrain
|
|
yea im about to pull my hair out. After I floor the pedal I still dont hear any clicks. I think I might take it to somebody with tranny experience.
|
|
Drivetrain
|
|
I was going to ask earlier, but is/was there more than just the trans in this sale. Did the bell housing, clutch fork/boot at least come with it? If not, then it definately isn't worth $300. FWIW, I think that as long as a person would drive either/o
|
|
Engine
|
|
.. It depends on the engine build/efficiency... a poorly tuned 7.6:1 350" may get 10 MPG... a 383" built with 2 eyebrow flattop pistons, FastBurnHeads, 11:1, good quench, and mild cam may get 25-30MPG... the details of the build are far mor
|
|
Restoration & Customization
|
|
their real proud of them LOL http://www.dixiemontecarlodepot.com/78-88montecarlo_subSections/s25.html
|
|
Authorized Vendors
|
|
You don't get the housings themselves, you install the kit shown below into your factory tail light housings:
|
|
Rolling Chassis
|
|
what springs are suggested with 2" drop spindles?
|
|
Your SS
|
|
Originally Posted By: robs 85ssLooks good, judging by the plates I'm guessing Croydon, PA? I think im about an hour north of you. Rob That would be correct.
|
|
All Things Electrical
|
|
Make sure the ground on the wiper motor is attached. Its the small metal "band" thats on the housing.
|
|
Non-Technical SS Discussion
|
|
Just wanted to let all the members know that GNS Performance is having a huge Holiday Special on Several Items!! Details can be viewed through this link: http://www.montecarloss.com/community/ubbthreads.php?ubb=showflat&Number=742089#Post742089
|
